GSY交流驗電器

 

技術參數
 
（1）6KV高壓驗電器 　　有效絕緣長度：840mm 手柄長度：120mm 節數：5 護環直徑：55mm 接觸電極長度：40mm 　　

（2）10KV高壓驗電器 　　有效絕緣長度：840mm 手柄長度：120mm 節數：5 護環直徑：55mm 接觸電極長度：40mm 　　

（3）35KV高壓驗電器 　　有效絕緣長度：1870mm 手柄長度：120mm 節數：5 護環直徑：57mm 接觸電極長度：50mm 　　

（4）110KV高壓驗電器 　　適用電壓等級：110KV 回態長度60cm 伸態長度200cm 　　

（5）220KV高壓驗電器 　　適用電壓等級：220KV 回態長度80cm 伸態長度300cm 　　

（6）500KV高壓驗電器 　　適用電壓等級：500KV 回態長度160cm 伸態長度720cm

使用方法及注意事項

使用驗電器時必須注意其額定電壓和被檢驗電氣設備的電壓等級相適應，否則可能會危及驗電操作人員的人身安全或造成誤判斷。驗電時操作人員應戴絕緣手套，手握在罩護環以下的握手部位，先在有電設備上進行檢驗，檢驗時應漸漸將驗電器移近帶電設備至發光或發聲時止，以確認驗電器性能完好，有自檢系統的驗電器應先撳動自檢鈕確認驗電器完好，然后再在需要進行驗電的設備上檢測，檢測時也應漸漸將驗電器移近待測設備，直至觸及設備導電部位，此過程若一直無聲、光指示，則可判定該設備不帶電，反之，如在移近過程中突然發光或發聲，即認為該設備帶電，即可停止移近，結束驗電。 另外，風車型驗電器只適用于戶內或戶外良好天氣下使用，凡雨、雪等環境條件下，禁止使用。 　
(1)用高壓驗電器進行測試時，必須戴上符合要求的絕緣手套;不可一個人單獨測試，身旁必須有人監護;測試時，要防止發生相間或對地短路事故;人體與帶電體應保持足夠的安全距離，10kV高壓的安全距離為0. 7 m以上.室外使用時，天氣必須良好，雨、雪、霧及濕度較大的天氣中不宜使用普通絕緣桿的類型，以防發生危險。 　　

(2)使用前，要按所測設備(線路)的電壓等級將絕緣棒拉伸至規定長度，選用合適型號的指示器和絕緣棒，并對指示器進行檢查，投人使用的高壓驗電器必須是經電氣試驗合格的。 　　

(3)對回轉式高壓驗電器，使用前應把檢驗過的指示器旋接在絕緣棒上固定，并用綢布將其表面擦拭干凈，然后轉動至所需角度，以便使用時觀察方便。 　　

(4)對電容式高壓驗電器，絕緣棒上標有紅線，紅線以上部分表示內有電容元件，且屬帶電部分，該部分要按《電業安全工作規程》的要求與臨近導體或接地體保持必要的安全距離。 

(5)使用時，應特別注意手握部位不得超過護環

(6)用回轉式高壓驗電器時，指示器的金屬觸頭應逐漸靠近被測設備(或導線)，一旦指示器葉片開始正常回轉，則說明該設備有電，應隨即離開被測設備。葉片不能長期回轉，以保證驗電器的使用壽命。當電纜或電容上存在殘余電荷電壓時，指示器葉片會短時緩慢轉幾圈，而后自行停轉，因此它可以準確鑒別設備是否停電。 　　

(7)對線路的驗電應逐相進行，對聯絡用的斷路器或隔離開關或其他檢修設備驗電時，應在其進出線兩側各相分別驗電。對同桿塔架設的多層電力線路進行驗電時，先驗低壓、后驗高壓，先驗下層、后驗上層。 　　

(8)在電容器組上驗電應待其放電完畢后再進行。 　　

(9)每次使用完畢，在收縮絕緣棒及取下回轉指示器放人包裝袋之前，應將表面塵埃擦拭干凈，并存放在干燥通風的地方，以免受潮。回轉指示器應妥善保管，不得強烈振動或沖擊，也不準擅自調整拆裝。 　　

(10)為保證使用安全，驗電器應每半年進行一次預防性電氣試驗。